把华为MA5626配置成普通三层交换机使用
内江市中川网维教你如何将华为MA5626配置Vlan中继变成普通三层交换机使用，简单分为三步。MA5626是华为技术有限公司推出的远端光接入单元。MA5626支持FTTB、FTTC组网应用，为小区用户提供语音、数据和视频业务接入。这就是它与普通交换机的区别。
第一步，清除MA5626交换机配置。命令如下
用户名：root
密码：mduadmin （这是默认的用户名和密码）
登陆MA5626后输入清除数据命令
enable ---回车
erase flash data ---回车
Y ---回车
然后输入重启命令
reboot system---回车
Y---回车
第二步，创建VLAN和VLAN业务模板，将我们所创建的VLAN加入VLAN业务模板中。
1、分别创建两个VLAN
huawei(config)#vlan 2 smart
huawei(config)#vlan 88 smart
2、创建VLAN业务模板
huawei(config)#vlan service-profile profile-id 1
huawei(config-vlan-srvprof-1)#forwarding vlan-mac //VLAN转发模式：VLAN+MAC地址（vlan-mac）
huawei(config-vlan-srvprof-1)#bpdu tunnel enable //打开二层网桥协议报文透传开关
huawei(config-vlan-srvprof-1)#user-bridging enable //打开二层网桥协议开关
huawei(config-vlan-srvprof-1)#commit //使用commit命令进行提交才能使配置生效
huawei(config-vlan-srvprof-1)#quit
3、将绑定VLAN与VLAN业务模板
huawei(config)#vlan bind service-profile 2 profile-id 1 //使用vlan bind service-profile命令将配置完成的VLAN业务模板与VLAN进行绑定
huawei(config)#vlan bind service-profile 88 profile-id 1
第三步，配置电口0/1/1为中继，使用service-port命令建立中继端口。将0/1/2-0/1/4配置为VLAN88的access口。将0/1/7-0/1/8配置为VLAN2的access口。
1、创建0/1/1业务虚端口为trunk中继，其中对应user-vlan为88，S-VLAN为88，业务流模板为6。另一个对应user-vlan为2，S-VLAN为2，业务流模板为6。
huawei(config)#service-port vlan 88 eth 0/1/1 multi-service user-vlan 88 rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 2 eth 0/1/1 multi-service user-vlan 2 rx-cttr 6 tx-cttr 6
2、将0/1/2-0/1/4配置为VLAN88的access口。
huawei(config)#service-port vlan 88 eth 0/1/2 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 88 eth 0/1/3 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 88 eth 0/1/4 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
3、将0/1/7-0/1/8配置为VLAN2的access口。
huawei(config)#service-port vlan 2 eth 0/1/7 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
huawei(config)#service-port vlan 2 eth 0/1/8 multi-service user-vlan untagged rx-cttr 6 tx-cttr 6
完整配置如下
MA5626(config)#
MA5626(config)#display current-configuration
{ <cr>|port<K>|section<K>|service-port<K>|simple<K>||<K> }:
Command:
display current-configuration
[MA5626V800R312: 2300]
#
[device-config]
<device-config>
port port-index 0/0/1 port-type GPON-PORT
#
[public-config]
<public-config>
snmp-agent local-engineid 800007DB0304B0E7C38D1606
#
[vlan-config]
<vlan-config>
vlan 2 smart
vlan 20 smart
vlan 88 smart
#
[vlan-srvprof]
<vlan-srvprof>
vlan service-profile profile-id 1 profile-name "srvprof-1"
bpdu tunnel enable
user-bridging enable
commit
vlan bind service-profile 2 profile-id 1
vlan bind service-profile 88 profile-id 1
#
[eth]
<eth-0/0>
interface eth 0/0
network-role 1 cascade
#
[gponnni]
<gponnni-0/0/1>
interface gponnni 0/0/1
password "%5L3_.^M^.9I<V@WN#JI1!!B#A8&)VAB']]F;U$19'2_1!!B#A8&)VAB']]F;U$19'
2_1!!%"
loid "%VL*&O__.3U3;RaK'0`"NPQ!!,DWUN(I=,'UZ_`@1RI<=WQ!!%"
checkcode "%L9;7+FT2-[LX3NU/Va@a]Q!!%"
#
[bbs-config]
<bbs-config>
service-port 0 vlan 2 eth 0/1/1 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 1 vlan 88 eth 0/1/1 multi-service user-vlan 88 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 2 vlan 88 eth 0/1/2 multi-service user-vlan 88 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 3 vlan 88 eth 0/1/3 multi-service user-vlan 88 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 4 vlan 88 eth 0/1/4 multi-service user-vlan 88 inbound
traffic-table index 6 outbound traffic-table index 6
service-port 5 vlan 2 eth 0/1/7 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 6 vlan 2 eth 0/1/8 multi-service user-vlan 2 inbound traffic-table index 6 outbound traffic-table index 6
service-port 7 vlan 2 eth 0/1/8 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 8 vlan 2 eth 0/1/7 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 9 vlan 88 eth 0/1/2 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 10 vlan 88 eth 0/1/3 multi-service user-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 11 vlan 88 eth 0/1/4 multi-service u ser-vlan untagged inbound
traffic-table index 6 outbound traffic-table index 6
service-port 12 vlan 20 eth 0/1/1 multi-service user-vlan 20 inbound
traffic-table index 6 outbound traffic-table index 6
#
[abs-config]
<abs-config>
config
#
[prevlanif]
<prevlanif>
interface vlanif20
#
[vlanif]
<vlanif20>
interface vlanif20
ip address 192.168.1.88 255.255.255.0
#
[meth]
<meth0>
interface meth0
ip address 192.168.0.2 255.255.255.0
#
[null]
<null0>
interface null0
#
[aaa]
<aaa>
aaa
authentication-scheme "default"
#
authorization-scheme "default"
#
accounting-scheme "default"
#
domain "default"
#
local-user "admin" password ""JZU.+!OI+_=EA>*VG'J!!!"
local-user "admin" privilege level 2
#
return